- 您现在的位置：买卖IC网 > Sheet目录323 > DV164132 (Microchip Technology)KIT EVAL F1 FOR PIC12F1/PIC16F1
F1 EVALUATION PLATFORM
USER ’S GUIDE
Chapter 6. Troubleshooting
6.1
6.2
INTRODUCTION
There may come a time when you need to determine why your F1 Evaluation Platform
is not performing correctly. This chapter lists a few of the problems that can prevent
proper operation.
COMMON PROBLEMS
6.2.1
The board will not power up
Make sure there is no shorting jumper at JP3. Then, go back and review Chapter
6.2.2
LCD is blank, but everything else works
The demo code in supplied with your F1 Evaluation Platform uses the Timer1 oscillator
to drive the LCD. If the Timer1 oscillator is not oscillating, the LCD will remain blank.
Here are some steps to assure that your Timer1 oscillator is working properly.
1. Clean and dry the board especially around the components at the top right corner
of the PIC16LF1937.
2. Make sure no foreign material is shorting the crystal leads.
3. If you are using the RC0 and RC1 pins for some other function, you should
modify lcd_init to reconfigure the LCD peripheral for a different clock
source.
The Timer1 oscillator of the PIC16LF1937 is a very low-power design that can be easily
disrupted by stray leakage. In an actual application, Microchip recommends that the
crystal circuit be conformal coated to prevent leakage. Please review Application Note
AN1288, “Design Practices for Low-Power External Oscillators” for more information.
6.2.3
The motor spins, but then stops
The BLDC start-up algorithm could be having trouble finding the BEMF zero-crossing
signal required to synchronize the motor commutation.
If you have attached the BLDC add-on board and you are using the supplied BLDC
motor, then the pot labeled iRef needs to be turned completely counter clockwise to
assure that a good BEMF zero-crossing signal is detected by the PIC16LF1937.
If you are using a different motor, you need to adjust the zero-crossing threshold to
match the requirements of the motor. For more information, consult the documentation
supplied with the BLDC add-on board.
? 2009 Microchip Technology Inc.
DS41401A-page 29
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
DV243003
KIT STARTER FOR SRL MEM PRODUCTS
DVA1001
ADAPTER FOR PIC16F716 18DIP
DVA1004
DEVICE ADAPTER 8/14/20DIP
E3R-D12GP-P
RELAY RCVR PLUG-IN DIMMER
E3R-R12-3HOTP
RCVR 3WIRE RELAY 120V
E3R-R12GP
RCVR PLUG-IN RELAY
E3T-MICFP-40
CONVERTER 4-CH SLT SENSOR
E3T-R12-2INTP
TRANSMITTER SWITCH LEG 120V
相关代理商/技术参数
DV164132
制造商:Microchip Technology Inc 功能描述:PIC12F1xxx/PIC16F1xxx F1 Evaluation Kit
DV164133
功能描述:电源管理IC开发工具 Energy Harvesting Development Tool
RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
DV164136
功能描述:开发板和工具包 - PIC / DSPIC PIC18F DEV Kit (with PICkit 3) RoHS:否 制造商:Microchip Technology 产品:Starter Kits 工具用于评估:chipKIT 核心:Uno32 接口类型: 工作电源电压:
DV164139
功能描述:开发板和工具包 - PIC / DSPIC Lo PIn Count USB Dev Kit (w/PICkit 3) RoHS:否 制造商:Microchip Technology 产品:Starter Kits 工具用于评估:chipKIT 核心:Uno32 接口类型: 工作电源电压:
DV17K3225T
制造商:SEI Stackpole Electronics Inc 功能描述:- Tape and Reel 制造商:SEI Stackpole Electronics Inc 功能描述:Var MOV 17VAC/22VDC 100A 27V 3225 SMD T/R
DV17K4032T
制造商:SEI Stackpole Electronics Inc 功能描述:VAR 17VAC 22VDC 250A 27V 4032 SMD - Tape and Reel 制造商:SEI Stackpole Electronics Inc 功能描述:Var MOV 17VAC/22VDC 250A 27V 4032 SMD T/R
DV18-145MB-3K
功能描述:端子 PIN -DSC 22-18 145X032 VYL RED RoHS:否 制造商:AVX 产品:Junction Box - Wire to Wire 系列:9826 线规:26-18 接线柱/接头大小: 绝缘: 颜色:Red 型式:Female 触点电镀:Tin over Nickel 触点材料:Beryllium Copper, Phosphor Bronze 端接类型:Crimp
DV18-145M-C
功能描述:端子 MALE BLADE ADAPT RoHS:否 制造商:AVX 产品:Junction Box - Wire to Wire 系列:9826 线规:26-18 接线柱/接头大小: 绝缘: 颜色:Red 型式:Female 触点电镀:Tin over Nickel 触点材料:Beryllium Copper, Phosphor Bronze 端接类型:Crimp